Alum-A-Pole Scaffolding System

The foundation of the Alum-A-Pole staging system. Made from special structural aluminum with Saf-T-Grip rubber on each end for secure pole-to-pole connections. Available in 6', 12', 18', and 24' lengths so they can be configured for virtually any working height. Each pole features four separate safety stops for added protection. The smooth, chatter-free design eliminates vibration during work, and the all-weather construction allows use in rain, heat, and cold. Over 1,000,000 Alum-A-Poles are in use worldwide.

The Alum-A-Joint is used to connect two Alum-A-Poles end-to-end for greater height. The joint provides a secure, rigid connection between poles of any combination — 6', 12', 18', or 24'. Joints are stackable, so multi-stage configurations simply use one joint per pole-to-pole connection. Required when working heights exceed a single pole length.

Alum-A-Braces secure the staging poles to the building for stability at height. Two types are available: foldable braces (used at the ground level or first stage of each pole) and rigid braces (used as intermediate braces when working above 24'). Each brace is secured to the building with Alum-A-Screws™ or 3" type AB screws — a minimum of 4 screws per brace is required. For configurations up to 24' height, one foldable brace per pole is sufficient. For heights above 24', add intermediate rigid braces at a maximum vertical spacing of 16' between braces.

The Pro-Jack is the telescoping staging bracket that holds the work platform at the correct working height. It extends telescopically and locks in position, supporting staging up to 27" wide. Load tested in excess of 4,000 lbs. The Pro-Jack features a comprehensive safety system: PRO-STRAP secures the jack to the pole, SAF-T-LOK CHAIN prevents accidental upending, AXIAL PERMA CLUTCH controls the raising and lowering mechanism, SAF-T-BRAKE with Secondary Disc Brake prevents uncontrolled descent, AUTO-GLIDE ensures smooth travel up and down the pole, SAF-T-CRANK is the raising handle, SAF-T-LATCH locks the jack at the desired height, and SAF-T-LATCH RESTRICTER prevents accidental unlocking.

The Pro-Bench is a telescoping aluminum work platform with an integrated guardrail. It is supported by two Pro-Jacks and provides staging up to 27" wide. The telescoping design allows the bench width to be adjusted to match job conditions. The built-in guardrail provides worker protection along the outer edge of the work platform.

The Alum-A-Scaff is an OSHA-recognized aluminum scaffold plank. It features structural square rungs for a secure working surface and No-Snow Decking™ that allows water, ice, and debris to fall through rather than accumulate. Individual planks can be joined infinitely — side-by-side for up to 24" wide staging or end-to-end for up to 24' long runs. The standard model A-1424 is 14" wide × 24' long and is rated for 2-man use. The Saf-T-Lok Chain prevents anti-twist and anti-upending of the plank during use.

The Saf-T-Net (Simm's) is a safety net that hangs below the work platform to prevent workers, tools, and materials from falling to the ground. Tested far in excess of OSHA static load requirements. It moves with the worker as the platform is raised or lowered. Maximum open area is 14 inches to ensure tools and small materials cannot fall through. Custom printing is available.

The End Rail System provides guardrail protection at both ends of the scaffold plank. One pair of end rails is used per staging configuration to cap the open ends of the Alum-A-Scaff planks and prevent workers from stepping or falling off the ends of the platform.

The Mudcap is installed on the base of each Alum-A-Pole to protect the pole end and prevent it from sinking into soft ground. It is removed and replaced with the Pro-Jack when the staging is assembled at the desired working height.